Today, there is an excellent use of Air compressors at the industry level and home-based projects for performing different jobs. Whether you are a construction worker or a carpenter, there is always a need for the air compressor. These are helpful in various tasks, including spray painting and framing nails. Your air compressor must have a specific size, power, and portability for performing multiple functions on Jobsite.
What is a Framing Nailer?
A framing nailer is a powerful tool used by construction workers or carpenters to help with the task of framing. In the old days, people used to operate a framing nailer by hand, which was a time taking process. Today, however, it is an effective tool for drilling nails more quickly and precisely. For working with this framing nail gun, you need a compatible air compressor that can enhance its performance during the process.
What Size Air Compressor Would Be Best For For Framing Nailer Job?
The size of the air compressor depends on your requirements, like whether you want to use it for commercial purposes or your house. Usually, a nailer needs a good airflow rate to perform a smooth and long-hour job. So, the recommended tank size of the compressor is 1-6 gallons, but for getting harder jobs, the airflow rate should be 2-5 cfm or higher @90 psi. With this cfm rate, you can do any job at home or on a construction project.
Examine Following Things Before Buying An Air Compressor For Framing Nailer
Some of the top air compressors for framing nailers were discussed above. If you are worried or confused about which compressor to buy from the above, you do not need to worry. We are here for you. Of course, we will guide you completely.
Buying guides based on our experiments, and we think you should consider those factors for purchasing a compressor which we are going to discuss below:
An air compressor’s power is measured in horsepower, a standard power unit. A high Hp compressor can more quickly build pressure inside the tank. But here, we need an air compressor for framing the nailer, so we need much higher horsepower than required people for commercial purposes.
The recommended horsepower (Hp) for air compressors ranging from 0.5 Hp to 1.5Hp is enough for framing the nailer.
The compressor’s size depends on requirements; our needs are not too much in this case. So, we should look for one easily adjustable compressor in our house, portable to carry that compressor anywhere and optimize noise level, so we have no problems while working this one.
The recommended size for a compressor is from 1 gallon to 6-gallon, which is suitable for framing the nailer.
Noise level is a critical factor in our recommendation for a compressor. Because, if you have a compressor that makes a high noise it will not create problems only for us. It will disturb our neighbors too, which is not a good thing.
So, the recommender compressor will be not more than 80 dB noise level as this is the optimized noise level for any compressor.
Easy to Move
Easy to move means we need a portable compressor to carry it to any point in our house. There are a lot of compressors in our suggestions that are portable enough to move from one location to another. Moreover, those compressors are also lightweight, which makes them more mobile. So, we recommend buying a portable compressor, and you can quickly move it alone in the house.
Features and Cabling
In framing nailers, we need an air compressor with enough features and cabling for our work. For example, what will we do if we buy a compressor with a short cord of power cable and we have to work at a distance from the outlets? Will we buy an extension? Which will increase the cost?
So, we should consider this point in our mind when we are going to buy a compressor for framing the nailer. Our recommendation is you buy a compressor which has a long power cord. Otherwise, you have to buy an extension for your work.
No doubt, affordable products are needed by every person, and they look for a cheap compressor for framing nailers in which we pay just what we get. The price range for the compressor, based on our recommendation, is $150 to $450.
This factor describes the structure or design of the compressor, whether the compressors design is vertical or horizontal. Because some people need vertical compressors to adjust compressors in the corner of their houses, and some need flats for their homes. So, depending on your need, buy a compressor with the structure vertical or horizontal.
When buying a compressor, we should look at how long the warranty the company is giving us. There are numerous businesses that offer warranties ranging from one year to ten years. Our recommendation is at least a warranty should be two years for the compressor. So, in case of if we face an issue, we can replace our compressor in a warranty claim.
Air pressure is gauged in psi, or pounds a square inch. This value determines how much the performance capability of your air compressor is. Small-size units with high PSI can allow your framing gun to run efficiently.
CFM is just basically how much air a compressor produces in one minute. Higher CFM means higher performance for your work. We recommend you go with a higher CFM to get excellent performance.
With the significant number of air compressors in the market, it is a big challenge to pick a suitable one. You must take into account various air compressor specs, including operational power, CFM, and tank size. Therefore, we bring this detailed article based on real-time testing. This article includes a list of 10 different best air compressor models for a framing nailer. Our team has listed them for you to review on these units before selecting any random air compressor from the marketplace.
Product Comparison At A Glance
|Name||PSI & CFM||Portabillity||Power||Quietness (Self Tested)||Warranty|
|BOSTITCH Pancake Air Compressor (BTFP02012)||2.6 CFM @ 90 PSI||Very portable because of (29 lbs) lightweight.||Requires 110V||78.5 dB||1 Year|
|California Air Tool (CAT-1P1060S)||1.2 CFM @ 90 PSI||29 lbs weight that is easy to move and very portable||Requires 110V||56 dB||1 Year|
|SENCO Air Compressor (PC1010)||1.4 CFM @ 90 PSI||Highly portable due to light weight of 20 lbs||Requires 115V||67 dB||1 Year|
|California Air Tool Compressor (CAT-1P1060SP)||1.2 CFM @ 90 PSI||Easy to move because of 29 lbs weight||Requires 110V||56 dB||1 Year|
|Makita MAC100Q Air Compressor||0.7 CFM @ 90 PSI||Highly portable with a weight of 25 lbs||Requires 120V||59 dB||1 Year|
|Metabo HPT Air Compressor (EC914S)||4 CFM @ 90 PSI||Easy to move & has 41 lbs weight||Requires 120V||71 dB||1 Year|
|DEWALT Air Compressor (D55146)||5 CFM @ 90 PSI||Heavyweight (80 lbs) & a bit difficult to move||Requires 120V||79 dB||1 Year|
|WEN Electrical Air Compressor (2289T)||4 CFM @ 90 PSI||Heavyweight (79.2 lbs), & a bit difficult to move||Requires 120V||72 dB||2 Year|
|Stealth Portable Air Compressor (SAQ-1301)||2.5 @ 90 PSI||It portable and have weight of 44 lbs||Requires 120V||64 dB||1 Year|
|Stealth Ultra Air Compressor (SAQ-1413)||3 CFM @ 90 PSI||Very heavy weight (101.1 lbs)||Requires 120V||65 dB||Lifetime Limited|
List Of 10 Best Air Compressors For Framing Nailers
1. BOSTITCH Pancake Air Compressor (BTFP02012)
We listed BOSTITCH Pancake Air Compressor on the top due to its effectiveness. It has a dynamic motor that can quickly start up even in a cold atmosphere. This air compressor gives its consumers 2.6 SCFM at 90 PSI which is highly compatible with the framing crew process.
But this is capable of producing maximum150 PSI. This beautiful compressor comes in compact form with high tank storage of up to 6 gallons/22.7 liters.
Its small size and lightweight (29 pounds) make this compressor handy and manageable. You can get from one place to another fast. In addition, it has a longer cord (5 feet), so you can move it anywhere. We love the design and the color scheme of this pancake shape machinery.
Though, all the features are hidden under the rigid regulator on the front. It features an oil-free pump that makes it more convenient as it requires no maintenance, and you can have this for years.
We needed to use the compressor for trimming the woodwork inside the house. So we decided to use the Bostitch pancake compressor. Despite its high noise level (78.5 dBA), it is relatively less noisy than the other air compressors and is best for in-house jobs. First, we decided to fill it out. It takes almost 2 minutes and thirty-nine seconds from empty point to full.
This model has two industrial M-style fittings regulated and controlled by a single dialer. We were using the 16 gauge framing nailer.
We managed to set the tank’s pressure at 100PSI with the help of a blow gun for direct air loss. Then set the regulated pressure at 25 PSI by moving the dialer located at the front.
Then we attached the 16 gauge finishing gun loaded with ½ inch nails with the air hose. After fixing this, we turned on the air compressor by pressing the red button at its front. Then pushed the gun against the wooden roof and shot the nail with the help of the trigger. It only used half tank capacity for completing the work on a 10×6 foot roof.
Overall, its performance was impressive. It’s pretty cool to have this portable air compressor. Though it’s a bit noisy, it is best for performing indoor tasks and many slow-firing jobs.
2. California Air Tool (CAT-1P1060S)
It will be perfect if you are looking for a noise-less air compressor for your home framing nailer projects. This CAT model can produce 1.2 CFM at 90 PSI and 1.60 CFM at 40 PSI. However, its maximum capacity is 120 PSI. The small unit gives users high portability. You can fit it anywhere, like below the bench or cabinets. Since it only weighs 29 pounds, you may move it from one place to another.
It has a 1-gallon steel storage tank that makes this unit fit for performing framing nailer projects. We like the most prominent feature that it has only 56 decibels of resonance. It makes this unit the quietest compressor and distinguishes it from the others.
Manufacturers tried to decrease noise by placing a silencing filter on the air-consuming point. These features make this unit 30% less loud than the other same-range compressors. Hence, it is the perfect compressor for framing nailers and indoor projects requiring less noise.
In addition, an oil-free pump increases its durability and functionality under any atmospheric conditions.
Our team decided to run a test of this one-gallon and less noisy air compressor for different nail guns. We noticed its fast building-filling process. It took only 53 seconds to fill the tank from 0 PSI to 120 PSI. As this small compressor comes with one outlet, we attached the air hose to this and joined the brad nailer for 18 gauge pins. Then the pressure was up to 100 PSI for running this air tool.
There are two gauges attached to the top of this small air compressor, left one allows one to read the tank pressure, while the other gauges the required pressure by air tool. After joining the gun, we start shooting the nails against a wooden plank.
During the process, we noticed that this unit took 17 seconds to recover the pressure. The noise level was too low that we were able to make a call by standing near this. By overwhelming this, we tested the air compressor’s capacity and started to fire the nails rapidly. After shooting the 19 pins, it started having issues driving nails flush with the board. It makes this unit efficient and can help to finish the work quickly.
So, our team concluded that this unit is the most reliable, quieter, and more portable air compressor. These features make this unit perfect for indoor framing crew jobs.
3. SENCO Air Compressor (PC1010)
According to our team’s experience working with different air compressors, SENCO PC1010 comes the third place. It is the best compressor for performing indoor framing nailer projects. We love its efficiency for quick trimming procedures. It is super compact, which makes it handier to use. It is transportable from one location to another.
It comes with a 0.5 HP motor and 1-gallon storage tank that makes it perfect for light repairing functions.
However, it can put out the maximum 125 PSI and gives 1.4 CFM, which is compatible with nail guns. This unit is made up of durable material and can last for years. Moreover, It also requires less maintenance because it has an oil-free pump. Nevertheless, it has only one hose, but its noise level is low. So it can be owned and used by any homeowner at any time of the day.
Its smaller size makes it easy to place it anywhere in the house. You can put it under the shelf as it is light usage machinery and can run by any breaker. You don’t have to be concerned that trimming will trip the breaker.
We run a test of this lighter air compressor on our oak boards. It took 2.35 minutes to pump up the pressure. While it took 42 seconds to build up the pressure again, this was a fast process. We tested on 18 gauge and 23 gauge pin nailers for shooting the 2 inches of nails.
It was pretty convenient to use due to its lighter weight. There are one tank pressure gauge and one line pressure gauge on the air compressor. We adjusted both pressure gauges according to our experiment’s needs. Then joined the framing nailer and started shooting the nails. It also has a cord that makes it reachable to the required position.
We also tried its functionality with the spikers. The process was not satisfactory. Therefore, it’s not suitable for running heavy pin nailers. On the whole, we would say it is an excellent option for trim work.
4. California Air Tool Compressor (CAT-1P1060SP)
This model of California Air Tool ultra-quiet Compressors brings some modern and upgraded features from the CAT-1P10606s model. It has similarities in most of the features such as 1 HP motor, single piston pump, and reparability of the pump. Additionally, it has a maximum pressure of 120 PSI and can deliver 1.2CFM to its users.
It comes with a 1-gallon tank with a similar material, i.e., steel. Identical to the previous version, its noise level is also 56 dBA. So it also falls in the category of the quietest air compressor. Almost all the manufacturing is the same as the previous model.
However, it comes with a modified design. It has a front panel on which regulators are fixed. It allows you to read the pressure readings easily. As compared to the old model, it weighs up to 29 pounds. Nevertheless, it is still listed in lightweight air compressors. So it is also easily movable from one location to other.
Moreover, this model also has a roll cage design that gives protection against falling. This feature makes this more reliable than the older model. It is a perfect match for a nail gun, brad gun, staple gun, and framing nailer.
This model and the preceding model are very similar. We decided to test to check whether it has the same performance level. After adjusting the pressure, we joined the framing nailer. Then we took a wooden board and started firing the 3-inch long nails.
It performs the same, as we have observed. The time for building pressure was 53 seconds, and for recharging, it was 15 seconds. Similarly, the efficiency and noise level were also the same.
Therefore, this is also the perfect model for in-house projects such as remodeling. If you are willing to pay the extra money, then go for this model to perform lighter home improvement projects.
5. Makita MAC100Q Air Compressor
It is another unit of the top air compressors. Makita MAC100Q is a compact air compressor. Therefore it is a highly capable and portable compressor. If you are searching for an ultra-quiet air compressor, this is the perfect option, as its noise level value is 58 dBA.
The highest pressure of this little 1-gallon tank compressor is 135 PSI, and it can create 7 CFM at that pressure. It might not be suitable for full-house projects, but it is perfect for remodeling. It has a double-piston motor system and a lower amperage value. It is only 25 pounds in weight, and its roll-cage manufacturers allow this air compressor to place under the chair or in the garage.
It has an oil-free pump built in, which boosts its durability. This compact air compressor meets every condition of lighting remodeling DIY work by using different air tools, including a brad nailer, finishing gun, and pin nailer.
We used Makita MAC 100Q, in this test to run different air tools, including the higher framing nailer. The small machinery has only one outlet, so we run the air tools one by one. First, I plugged in the unit to fill the pressure; it took 1.06 minutes to build up the total force. Then we adjusted the pressure according to our air tool. First, we experimented on brad nailer. It allowed us to shoot the nails efficiently.
Then we tested its capacity for framing the nailer. However, it is not recommended to run for heavy air-tool. We ran this just to check its functionality. So, when the time comes and we will not have another option, whether we can use it or not. It also worked well for framing nailers. But for this purpose, it is not suitable for permanent use.
Having this efficient air compressor could be a lifesaving decision.
6. Metabo HPT Air Compressor (EC914S)
Metabo HPT is one of the top ten air compressors. It is suitable to perform multiple tasks. So if you are looking for an air compressor that can power up more than one framing nailer, this 6-gallon air compressor would be perfect. Metabo HPT-EC914s is the updated model of previous models. It has upgraded features. It can handle the 4CFM at 90 PSI, making it a dynamic unit. It also works nicely for 5.1 CFM at 40 PSI. But it comes with the feature of producing a maximum of 200 PSI.
This air compressor model is also oil-free, making it durable and cost-effective for years. In addition, it has a little bit higher weight which is 41pounds. However, this does not imply that you cannot carry it because it is too heavy. It has a metal rod on top that can use to move it from one location to another. Besides, it comes with 7 feet long cord that makes it easy to place anywhere on the working site.
We examined its dynamic functionality while running a test. We tested its compatibility with nail guns, including finish, brad, and framing nailers. The air pressure took about 3 minutes to increase after being turned on. You can utilize both of the nearby outlets that come with this pancake unit at once. After adjusting the required PSI, we fixed the nailer into the outlet. A finishing nailer was used to shoot the 16 gauge nails. It was an incredible experience while working through this.
We decided to run the framing nailer as it can handle heavy nailers. A framing nailer is a more severe air tool that requires a heavy-duty air compressor. While experimenting with this pancake air compressor, we faced no difficulty or disruption in running these multiple tools. We finished the work by unhooking the air tools. Then a drain valve under the tank was opened to empty the tank.
It would be best to purchase this air compressor for working on your whole house project.
7. DEWALT Air Compressor (D55146)
Here comes another air compressor available in the market for remodeling and DIY projects. DEWALT-D55146 is an oil-free and maintenance-free air compressor. It has a 1.6 HP and 4.5-gallon air storage tank. It can produce 5 SCFM at 90 PSI. It has a maximum ability of 200 PSI It is sometimes referred to as a powerful air compressor.
It has a distinctive shape and style and can be placed or stored anyplace. You can quickly put it in the truck and fix it nicely underneath the tables. Additionally, keeping this vertical will take up less area. The tires on this unit are vast and friendly, which makes it easy to carry and roll around from one place to another. Despite its weight (80 pounds), this feature makes its movability easier.
The shape is semi-flat which is different from other pancake air compressors. You can quickly move this without bumping into other things. Besides the light framing crew process, this could benefit heavy work.
As we examined our top 10 listed air compressors for framing nailers, we tested the DEWALT-D55146. This tool has the most significant capacity and compatibility with different tools. We plugged in the compressor, allowing it to reach up to 200 PSI. This process took almost 1.35 minutes to complete. In contrast, the recovery time was 22 seconds for this limited PSI.
It worked pretty efficiently. Within a few minutes, we had done the job. Moreover, these heavy-duty units are perfect for different processes such as roofing, framing, trim carpentry, remodeling, and deck building.
Overall it is worth buying a compressor if you always need to perform multiple tasks. However, you can use other lighter air compressors if you want delicate trimming.
8. WEN Electrical Air Compressor (2289T)
If you are looking for multiple-task air compressors, then the WEN-2289T unit is the best selection. The more robust and powerful machinery can provide extreme services for many years.
It is a vertical oil-free compressor that perfectly matches pneumatic tools such as blow guns and framing nailers. It has a 10-gallon air storage tank which is made of steel. It can produce a maximum pressure of 150 PSI, which makes it suitable for running 100 PSI air tools.
You don’t have to bother about its upkeep because it has an oil-free pump. Due to this, it is a pretty reliable and durable air compressor. It has an easy-to-reach drain valve on the upper-back side of the unit. It has two pressure gauges, one for measuring the tank pressure and one for adjusting the required force.
This vertical air compressor weighs up to 79.2 pounds, making it heavy. For transporting this air compressor, it is also equipped with a rubber handle and two large wheels. So carrying this air compressor through the congested area is easy as there is no fear of bumping into other things or equipment.
Working with a 10-gallon WEN-2289T unit was an impressive experience. After plugging in the compressor, we built up the pressure. Pumping up a 10-gallon compressor was relatively easy and quick. It took approximately 7 minutes for this process.
After reaching its maximum PSI (150 PSI), the auto-shut-down function turned on and allowed the compressor to turn off. Then we hooked up our framing nailer through its quick-couples air outlet. During the crew’s shooting process, we noticed that this unit allowed us to work smoothly. Draining the moisture was a quick process through the drain valve.
So we found this unit to a maintaining free and efficient air compressor. It would be a perfect partner for homeowners and carpenters for running various functions from framing nails to paint.
9. Stealth Portable Air Compressor (SAQ-1301)
SAQ-1301 model of Stealth portable air compressor is at the 9th number on the list. It is categorized as an ultra-quiet compressor as it produces 67 decibels. It is a constructional model suitable for framing, nailing, finishing, and trimming. It comes with 3.5 CFM at 40 PSI and 2.5 at 90 PSI, so it does not have that much power for running heavy gadgets. But it perfectly matches the 100 PSI framing nailer.
One feature of this unit is it has more break-in time. Other compressor needs a maximum of 10 minutes to drain out. But this unit takes 30 minutes to drain out. This hot-dog-style model comes with a 3-gallon tank and weighs 44 pounds. It means it is not easy to carry from one place to other. Though there is one handle at the top, which gives a proper grip for carrying the unit. It will be the best choice if you want a highly suitable performance and less noisy air compressor for a finishing or trimming project.
We tested its running cycle using the 18 gauge nailer and calculated the filling pressure time of the 3-gallon tank compressor. It took 1.45 minutes to complete building up the pressure. Then an 18 gauge nailer was attached to check its running ability.
Outlet and pressure gauges are present on the top of the compressor. The air hose was fastened to the outlet when the pressure reached at 100 PSI. Then one team member started shooting the 18 gauge nails into the wooden plank. We noticed that it has a capacity of up to 20 18-gauge nails at a time. Besides, the recovery time was 37 seconds which is quite impressive.
The finishing period was longer than the other standard compressors. However, overall performance was good, which makes it suitable for a framing nailer.
10. Stealth Ultra Air Compressor (SAQ-1413)
This air compressor also falls in the most durable and quiet air compressor category. It can fulfill the requirements of remodelers as well as DIYers. It is an ideal air compressor for more accessibility to the most challenging jobs.
As for the noise level, it has less noise rating than the other standard compressors. It is about 64 decibels which makes it a quieter unit. It comes in a unique style which is twin stack. It has a 4.5-gallon tank capacity located at the front. Its motor is fixed at the back side and rated as 1.3 HP.
It gives its users the 3CFM at 90 PSI and can produce up to 150 PSI. Another unique feature of this compressor is that it comes with a telescopic handle. You can quickly fix and clamp this handle at one point.
This high CFM compressor is appropriate enough to run different tools such as brad nailers, finish guns, blow guns, and framing nailers. Although it has a high cost, it gives much power and efficiency for running tasks.
As Stealth (SAQ-1413) comes with a single outlet, you can only run one air tool at once. Nevertheless, it is a high-power air compressor but can run a single air tool, requiring high CFM. We tested its competence for brad nailer by shooting the nails in the wood board. The measured recycle time was 30 seconds.
Though it is competent to run light tools, it is not suitable for running high CFM tools. We noticed its efficient working and quieter performance during the process. In the end, we finished the process by releasing the water through the drain valve on its left side. We do have a quieter unit for performing the various tasks would be a wiser choice.
Comparison of Our 2 Top Picked Air Compressors for Framing Nailer
Now we will give you a brief comparison of our top-picked compressors with the other compressors. This comparison is based on size, pump uptime, and recovery period.
BOSTITCH Pancake Air Compressor (BTFP02012)
It is the ideal air compressor for framing nailers, based on our testing results. Since this is a 6-gallon pancake air compressor that is not heavy, it is the best portable, efficient, and suitable to run in any weather. In short, it is the best air compressor for DIYers and carpenters.
California Air Tool (CAT-1P1060S)
CAT-1P1060S is the second-best air compressor that we found during our testing period. It is also a durable and portable unit that you can have. We put this in the second due to its lower CFM rate than the BOSTITCH pancake compressor. However, it could be the perfect option to perform with framing nailers.
In conclusion, there are a few things you should focus on whether you are looking for the best air compressor framing nailer for your home construction work or any other building project. Our team tested the various air compressors and brought you the list of the 10 best air compressors. This list is based on their provided CFM, PSI, and compatibility with the different pneumatic tools, including framing nailers. To receive comprehensive information, make sure to read the entire article.
How much cost of an air compressor for framing nailer?
The cost of an air compressor should be reasonable for framing a nailer. For framing, you can buy an air compressor, which ranges from $120 to $450.
Can you operate framing nails with a pancake compressor?
Yes, you can simply use a frame nailer with a pancake compressor. Most of the framing nailer requires 100 PSI to run correctly. A pancake compressor manufactures to produce more than 100 PSI so that it can be compatible with framing nailers.
Read Other Buying Guides